HS Agitators
HS Side-Entering Agitators offer the same ruggedness, dependability and simplicity of design found in our other high-quality turbine agitators and mixers. At the heart of the HS Agitator is a right-angle drive exclusively engineered for side-entering agitator service.
Chemineer ® HS Side-Entering Turbine Agitators work efficiently when a tank is too large for convenient installation of a top-entering agitator, or where headroom is severely limited. Supporting a top-entering agitator on a large tank is often far more expensive than the installation of a side-entering agitator. Long shafts on extremely tall tanks can be eliminated for cost savings and design simplicity. For large tank installations, several smaller side-entering agitators may be more efficient and economical than a single, larger unit.
The HS Agitator is available in four standard sizes from 1 to 75 hp. Special designs, up to 250 hp, are available. The wide range of power selections and seal options, combined with two standard output speeds and accurately sized impellers, means that there is an HS agitator available for nearly every standard application. Consider HS Side-Entering Agitators for process applications involving continuous blending, heat transfer, mass transfer or solids suspension.
- Specifications
- Technical Data
- Advantages
- Industries
- Applications
- Contact
Specifications
Operating Parameters:
- Flows to 565 m³/h (2500 gpm)
- Heads to 110 m (350 ft)
- Pressures to 17 bar (250 psi)
- Temperatures from -30°C (-20°F) to 90°C (200°F)
Shaft Metallurgy Options:
- 316 SS
- Alloy 20
- Hastelloy
- Titanium
Features:
- Full basket strainer
- NEMA in-line motor
- Fiberglass mounting plate
- Tapered “Polygon” impeller drive
- “Pull-out” bearing retainers
- Level controls
Options:
- Simplex and duplex pit covers
- Float switches
- Particulate separators
- Non-metallic lubrication lines
- Tailpipe
Technical Data
- Engineered Polymer Composite Construction offers cost-effective corrosion-resistance, is lightweight, non-galling, non-sparking, and non-conductive.
- Unitized Case with Integrally Molded Flanges at the suction and discharge nozzles, fully gusseted for structural soundness.
- Externally Adjustable, Semi-Open Impeller provides consistently high efficiencies and minimizes maintenance.
- Shaft/Bearing System operates below the first critical speed for less shaft whip and longer bearing life.
- Bearings can be lubricated by external flush or self-lubricated by the pump fluid.
- Single-Piece Column is lightweight, filament-wound, reinforced fiberglass composite for strength and rigidity.
Advantages
- Lightweight and corrosion-resistant due to engineered polymer composite construction.
- High efficiency and minimal maintenance with externally adjustable impeller.
- Long bearing life with low shaft whip and flexible lubrication options.
- Robust construction with unitized case and reinforced single-piece column.
Industries
- Leaching Acid
- Chemical and Liquor
- Caustic and Chlor-Alkali
- Bleach Chemicals
- Auxiliary
- Acid Transfer
- OEM
- Water Treatment
- Water Supply and Distribution
- Wastewater Collection and Treatment
- Polymers
- Plating, Galvanizing and Other Coatings
- Pharmaceuticals
- Automotive and Aircraft
Applications
- Corrosive Services
- General Purpose
- Water Treatment
- Pulp and Paper
- Chemical Processing
- Utility
- Metal and Steel Industry
- Pollution Control
- Plating
Contact our Pump Specialist Team
- Phil Soltan (External) – mob: 086 185 3782
- Adrian McSweeney – tel: 021 461 7212
- Paul-Fox Morris – tel: 021 461 7231
- Una Long (Pump & Service Support) – tel: 021 431 7200
- Tel: 021 461 7200
-
PumpsNETZSCH
Progressive Cavity Pump
-
PumpsFlowserve
SIHI SuperNova Pump ZDN – Hot Water
-
PumpsNETZSCH
Multi Screw Pump
-
PumpsFlowserve
Mark 3 Recessed Impeller Pump
-
Mixing TechnologyChemineer
Chemineer HS Turbine Agitators
-
Mixing TechnologyGreerco
Greerco Pipeline Mixers
-
PumpsFlowserve
PolyChem S-Series ANSI Overhung, Non-Metallic Pump
-
PumpsFlowserve
Durco Mark 3 Pump – ANSI/ASME standard
Need help with finding the right technical solution?