The Zook PB Bursting Disc mounts with the concave surface facing the process media. As pressure increases above the recommended operating pressure, the disc will bulge until it reaches the maximum tensile strength of the material and ruptures.
Zook PB Bursting Disc – Forward Acting
Process Equipment
Zook
Send Enquiry
- Operating pressures to 70% of the disc’s marked burst pressure
- Seat Configuration: Angular 30°
- Sizes 1/4″ thru 24″ diameters
- Temperature ratings to 900°F (482°C)
Options:
Vacuum Supports are required for vacuum services. Vacuum supports are attached to the process side of the disc and allow the disc to support a full system vacuum.
Liners / Coatings Teflon liners are available to provide protection from corrosive media if required. Coatings are also available. Refer to (Table 1 in Spec Sheet) for maximum temperature ratings for disc, liner and coatings.
Protective Rings can be used with Zook PB Bursting Disc to provide stability and protection when thin materials and/or liners are used.
Zook 7A Holder – Angle Seat Disc Holders
- Specifications
- Technical Data
- Advantages
- Industries
- Applications
- Contact
Specifications
Operating Parameters:
- Flows to 565 m³/h (2500 gpm)
- Heads to 110 m (350 ft)
- Pressures to 17 bar (250 psi)
- Temperatures from -30°C (-20°F) to 90°C (200°F)
Shaft Metallurgy Options:
- 316 SS
- Alloy 20
- Hastelloy
- Titanium
Features:
- Full basket strainer
- NEMA in-line motor
- Fiberglass mounting plate
- Tapered “Polygon” impeller drive
- “Pull-out” bearing retainers
- Level controls
Options:
- Simplex and duplex pit covers
- Float switches
- Particulate separators
- Non-metallic lubrication lines
- Tailpipe
Technical Data
- Engineered Polymer Composite Construction offers cost-effective corrosion-resistance, is lightweight, non-galling, non-sparking, and non-conductive.
- Unitized Case with Integrally Molded Flanges at the suction and discharge nozzles, fully gusseted for structural soundness.
- Externally Adjustable, Semi-Open Impeller provides consistently high efficiencies and minimizes maintenance.
- Shaft/Bearing System operates below the first critical speed for less shaft whip and longer bearing life.
- Bearings can be lubricated by external flush or self-lubricated by the pump fluid.
- Single-Piece Column is lightweight, filament-wound, reinforced fiberglass composite for strength and rigidity.
Advantages
- Lightweight and corrosion-resistant due to engineered polymer composite construction.
- High efficiency and minimal maintenance with externally adjustable impeller.
- Long bearing life with low shaft whip and flexible lubrication options.
- Robust construction with unitized case and reinforced single-piece column.
Industries
- Leaching Acid
- Chemical and Liquor
- Caustic and Chlor-Alkali
- Bleach Chemicals
- Auxiliary
- Acid Transfer
- OEM
- Water Treatment
- Water Supply and Distribution
- Wastewater Collection and Treatment
- Polymers
- Plating, Galvanizing and Other Coatings
- Pharmaceuticals
- Automotive and Aircraft
Applications
- Corrosive Services
- General Purpose
- Water Treatment
- Pulp and Paper
- Chemical Processing
- Utility
- Metal and Steel Industry
- Pollution Control
- Plating
Contact our Pump Specialist Team
- Phil Soltan (External) – mob: 086 185 3782
- Adrian McSweeney – tel: 021 461 7212
- Paul-Fox Morris – tel: 021 461 7231
- Una Long (Pump & Service Support) – tel: 021 431 7200
- Tel: 021 461 7200
-
PumpsNETZSCH
Progressive Cavity Pump
-
PumpsFlowserve
SIHI SuperNova Pump ZDN – Hot Water
-
PumpsNETZSCH
Multi Screw Pump
-
PumpsFlowserve
Mark 3 Recessed Impeller Pump
-
Mixing TechnologyChemineer
Chemineer HS Turbine Agitators
-
Mixing TechnologyGreerco
Greerco Pipeline Mixers
-
PumpsFlowserve
PolyChem S-Series ANSI Overhung, Non-Metallic Pump
-
PumpsFlowserve
Durco Mark 3 Pump – ANSI/ASME standard
Need help with finding the right technical solution?