CORA Steri Lift
The CORA Steri Lift is a drum, bin or bag positioner/lift/mixer that can be used in sterile rooms, and which allows quick and efficient process handling. The experience in facing the complexity of the strict norms.
The main characteristics of the CO.RA. “STERI LIFT” is the hydraulic piston, completely enclosed in a carter. Any kind of contamination is avoided thanks to the perfect seal, as all movements are
motorized through a motor/hydraulic pump with electric drive. The motor is located inside the base of the STERI LIFT itself, while it’s casing (in AISI 304 stainless steel) provides insulation from the working environment. The absence of exposed chains, gears, guides, eyelets and electrical and mechanical parts, as well as its realization with rounded surfaces, makes cleaning operations of the CORA Steri Lift easy.
The CORA Steri Lift complies with the recommendations of GMP (Good Manufacturing Practice) ensuring maximum protection of health and the prevention of accidents to the operator during the work cycle. The surface of the stainless steel parts not in contact is satin Ra 0,8 finished. Upon request and depending on the zone where it is installed, the Steri Lift can be supplied completely polished. The STERI LIFT, once correctly installed in its service position, is always ready to be used. Its typical installation is on the ground, but special ceiling mounted versions are also available.
- Specifications
- Technical Data
- Advantages
- Industries
- Applications
- Contact
Specifications
Operating Parameters:
- Flows to 565 m³/h (2500 gpm)
- Heads to 110 m (350 ft)
- Pressures to 17 bar (250 psi)
- Temperatures from -30°C (-20°F) to 90°C (200°F)
Shaft Metallurgy Options:
- 316 SS
- Alloy 20
- Hastelloy
- Titanium
Features:
- Full basket strainer
- NEMA in-line motor
- Fiberglass mounting plate
- Tapered “Polygon” impeller drive
- “Pull-out” bearing retainers
- Level controls
Options:
- Simplex and duplex pit covers
- Float switches
- Particulate separators
- Non-metallic lubrication lines
- Tailpipe
Technical Data
- Engineered Polymer Composite Construction offers cost-effective corrosion-resistance, is lightweight, non-galling, non-sparking, and non-conductive.
- Unitized Case with Integrally Molded Flanges at the suction and discharge nozzles, fully gusseted for structural soundness.
- Externally Adjustable, Semi-Open Impeller provides consistently high efficiencies and minimizes maintenance.
- Shaft/Bearing System operates below the first critical speed for less shaft whip and longer bearing life.
- Bearings can be lubricated by external flush or self-lubricated by the pump fluid.
- Single-Piece Column is lightweight, filament-wound, reinforced fiberglass composite for strength and rigidity.
Advantages
- Lightweight and corrosion-resistant due to engineered polymer composite construction.
- High efficiency and minimal maintenance with externally adjustable impeller.
- Long bearing life with low shaft whip and flexible lubrication options.
- Robust construction with unitized case and reinforced single-piece column.
Industries
- Leaching Acid
- Chemical and Liquor
- Caustic and Chlor-Alkali
- Bleach Chemicals
- Auxiliary
- Acid Transfer
- OEM
- Water Treatment
- Water Supply and Distribution
- Wastewater Collection and Treatment
- Polymers
- Plating, Galvanizing and Other Coatings
- Pharmaceuticals
- Automotive and Aircraft
Applications
- Corrosive Services
- General Purpose
- Water Treatment
- Pulp and Paper
- Chemical Processing
- Utility
- Metal and Steel Industry
- Pollution Control
- Plating
Contact our Pump Specialist Team
- Phil Soltan (External) – mob: 086 185 3782
- Adrian McSweeney – tel: 021 461 7212
- Paul-Fox Morris – tel: 021 461 7231
- Una Long (Pump & Service Support) – tel: 021 431 7200
- Tel: 021 461 7200
-
PumpsNETZSCH
Progressive Cavity Pump
-
PumpsFlowserve
SIHI SuperNova Pump ZDN – Hot Water
-
PumpsNETZSCH
Multi Screw Pump
-
PumpsFlowserve
Mark 3 Recessed Impeller Pump
-
Mixing TechnologyChemineer
Chemineer HS Turbine Agitators
-
Mixing TechnologyGreerco
Greerco Pipeline Mixers
-
PumpsFlowserve
PolyChem S-Series ANSI Overhung, Non-Metallic Pump
-
PumpsFlowserve
Durco Mark 3 Pump – ANSI/ASME standard
Need help with finding the right technical solution?